Miscellaneous Lifeline Fittings - Machine Swage
Diamond Pad Eye
1/4" Bail
Stanchion Eye
1" Stanchion
Pulpit Anchor
1" Rail
2-5/8"
1-1/2"
This pad eye can be used on deck for life lines or other applications. 750 lbs safe working load. See our hinged pad eyes on page 45. Diamond Pad Eye Cat. No. 28-501
This fitting is used on a stanchion for adding lower life lines without the need to drill holes for the cable to pass through. (5/16" hole). Stanchion Eye Cat. No. 29-502
Can be used on the stern rail and bow pulpit to terminated jaw fittings for lower (or upper) life lines. (1/2" hole). Pulpit Anchor Cat. No. 29-501
Eye to Deck Toggle Fitting
Gate Stop
This fitting can be mounted to any flat surface and accept life line fittings, line, etc. Toggling action is 140 degrees. Eye to Deck Toggle Cat. No. LS-2550
These collars can be used at the gate instead of interlocking eyes, they maintain tension while the gate is open. A set-screw holds them in place. 29-503 29-504 29-505 29-506 3/16" max coating 1/4" max coating 5/16" max coating 3/8" max coating
Eye to Jaw Fitting
Conversion Sleeve
36-610
Allows the use of 3/16" life line fittings to be used with 1/8" cable. Slide over cable first then into fitting. 1/8 to 3/16" Machine Swage
This fitting will convert a small bail at the stern rail to our standard gate eye to accept our Over Center Gate Hook. Eye to Jaw Cat. No. LS-2500
Stanchion Terminal
a b
19 Series "Shortie" Turnbuckle
Used where the cable needs to be terminated at the stanchion. a a a b 25-305-5F 25-306-5F 25-308-7-5F 100-110-1 5/32" wire 3/16" wire 1/4" wire (7/32" die) 1/8" wire (true 1/8" terminal)
Regular
Terminal to Terminal Fitting
"Shortie"
All 1/4-28 (unslotted) body life line turnbuckles are available in a new shorter length. Body length is 3" for 2" of total adjustment. Add "S" to std. cat. no., same price.
Length 4" Used whenever two pieces of cable need to be joined. 25-316-5-6 Swage to Swage Stud 3/16"
12
Johnson Marine * Tel 860.873.8697 * Fax 860.873.8589 * www.csjohnson.com
Life Line Replacement Parts - Machine Swage
Life Line Studs for Machine Swaging (T-316 S/S)
CATALOG NUMBER
30-601 30-602 30-602-1 30-603 30-603-1 30-604 30-604-1 30-605*** 30-621 30-621-1 30-622 30-623 30-623-1 30-606* 30-607* 30-607-1* 30-608* 30-608-1* 30-608S 30-608-1S 30-609* 30-610*** 30-611 30-611-7** 30-612 30-612-2 30-613 30-613-1 30-613-7** 30-613-1-7** 30-615** 30-615-1** 30-615-1S**
THREAD SIZE
1/4-28 L.H. x 3/8 1/4-28 L.H. x 1-1/2 1/4-28 R.H. x 1-1/2 1/4-28 L.H. x 2-1/2 1/4-28 R.H. x 2 1/2 10-32 R.H. x 3 10-32 L.H. x 1-7/8 1/4-28 L.H. x 2-1/2 1/4-28 L.H. x 2-1/2 1/4-28 R.H. x 2-1/2 1/4-28 L.H. x 3/8 1/4-28 L.H. x 1-1/2 5/16-24 L.H. x 2 5/16-24 L.H. x 3/8 5/16-24 L.H. x 2 5/16-24 R.H. x 2 1/4-28 L.H. x 2-1/2 1/4-28 R.H. x 2-1/2 1/4-28 L.H. x 1-1/2 1/4-28 R.H. x 1-1/2 1/4-28 R.H. x 3-3/4 1/4-28 L.H. x 2-1/2 3/8-24 L.H. x 3/8 5/16-24 L.H. x 3/8 3/8-24 L.H. x 1-1/2 5/16-24 L.H. x 2 3/8-24 L.H. x 3 3/8-24 R.H. x 3 3/8-24 L.H. x 3 3/8-24 R.H. x 3 5/16-24 L.H. x 2-3/4 5/16-24 R.H. x 2-3/4 5/16-24 R.H. x 1-1/2
WIRE SIZE
1/8" 1/8" 1/8" 1/8" 1/8" 1/8" 1/8" 1/8" 5/32" 5/32" 5/32" 5/32" 5/32" 3/16" 3/16" 3/16" 3/16" 3/16" 3/16" 3/16" 3/16" 3/16" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4" 1/4"
CAT # USED ON
22-301 & 302 23-303 Termianl Tuner, "S" Series 20-304, 21-304, 19-314 & 21-884 GENERAL 23-302 19-314-2 23-301, 19-324, 42-314 19-315-2, 325, 21-305, 24-304, 42-315 19-315-2, SPECIAL 22-307 & 22-308 24-305 21-413, 21-885 22-303 & 304 21-886, 24-303, 21-410/411 GENERAL 20-306, 21-306, 19-316 SPECIAL "S" Series "S" Series Terminal Tuner, "S" Series GENERAL 24-301, 19-326, 42-316 22-305, 306 22-305/6-7 GENERAL 21-888, 21-412 GENERAL GENERAL GENERAL GENERAL GENERAL GENERAL Terminal Tuner, "S" Series
* Note - 3/16" terminals may be used for 1/8" wire - Order #36-610 sleeve ** Note - These studs must be swaged using a 7/32" die *** Note - Cross drilled
Johnson Marine * Tel 860.873.8697 * Fax 860.873.8589 * www.csjohnson.com
13
