Rigging Hardware
Stay Adjuster - Quick Release
Developed for dry sailed one-design dinghies. When the Quick Release pin is pulled, easy adjustment and unrigging can be obtained.
NOTE: Quick Release Pins available - see chart page 37.

Specifications & Data
CAT. NO.
15-212

WIRE TERMINAL PIN
3/16"

CHAIN PLATE PIN
1/4"

MAX. WIRE SIZE
1/8"

PIN TO PIN ADJUSTMENT
1 3/4" to 3 5/8"

SAFE WORKING LOAD
400 lbs.

Stay Adjuster - Calibrated
Here is an extremely functional stainless steel fitting. Adjustment is made by turning the knurled nut. The terminal rod is made captive, therefore it cannot turn and cannot come apart even when fully extended. It produces a "fool proof" adjuster which cannot come apart either by an inexperienced crew or during the vibration of trailering on the road. Patent Number 3938844

Specifications & Data
CAT. NO.
11-100 11-102 11-103 12-100 12-104 12-105

TYPE
Jaw/Eye Jaw/Swage Jaw/Swage Jaw/Eye Jaw/Swage Jaw/Swage

WIRE SIZE
1/16", 3/32" *1/16" 3/32" To 5/32" 1/8" 5/32"

APPROX. BREAKING STRENGTH
1,000 lbs 1,000 lbs. 1,000 lbs. 3,000 lbs. 3,000 lbs. 3,000 lbs.

THREAD SIZE
10-32 10-32 10-32 1/4-28 1/4-28 1/4-28

LENGTH
Closed 5" 2" adj. 2" adj. 5 5/8" 2 3/4" adj. 2 3/4" adj. 8 3/8" Open 7"

PIN DIA
3/16" 3/16" 3/16" 1/4" 1/4" 1/4"

SWL
400 lbs 400 lbs 400 lbs 1000 lbs 1000 lbs 1000 lbs

1

2

*Swage with 3/32" die.

Replacement Knurled Nuts: Order Cat#35-623 for 10-32 thread, Cat#35-624 for 1/4-28 thread.

Shroud Adjusters - Single Row Hole
These single row hole adjusters are good for applications where precise tuning is not required.

Specifications & Data
CAT. NO.
1 2 15-203 15-205*

TOTAL ADJ.
3-1/4" 2 5/8"

INCREMENT
9/64" 3/8"

PIN DIAMETER
3/16" 1/4"

JAW WIDTH
3/8" 5/16"

SWL
400 lbs 1000 lbs

*Calibrated

Shroud Adjusters - Double Row Hole 3 4
These double row hole adjusters offer more precise tuning for stays and shrouds.

Specifications & Data
CAT. NO.
3 4 15-204-1* 15-204

TOTAL ADJ.
2 1/2" 2 1/2"

PIN DIAMETER INCREMENT
5/32" 5/32"

UPPER
3/16" 3/16"

LOWER
1/4" 3/16"

JAW WIDTH
3/8" 3/8"

SWL
400 lbs 400 lbs

*Calibrated

26

Johnson Marine * Tel 860.873.8697 * Fax 860.873.8589 * www.csjohnson.com

Rigging Hardware
Quick Release Levers
The Johnson Hyfield Type Lever has a number of very practical features that have been developed after extensive testing on both high performance multihulls and monohulls. The fitting is rugged, having an ultimate strength of 2500 lbs. A positive stop is provided to prevent jamming fingers between fitting and wire when thrown open under load and the large surface area of the push pad makes it easier to close lever under load. Lever take-up is 2 1/8" to an over-center position and comes with a quick release pin for positive locking. The extender arm may be had in either 1/4" or 5/16" pin size. This is an essential piece of hardware on Catamaran shrouds to allow the crew to right the boat after a capsize, without it, another boat or extraordinary effort is required. Trailerable boats up to 26 feet find that a lever on the forestay greatly facilitates stepping and unstepping the mast.
NOTE: Quick Release Pins available - see chart page 37

Specifications & Data
CAT. NO.
14-205 14-206

EXTENDER # OF HOLES
3 4

WIRE SIZE
To 1/8" To 5/32"

APPROX. BREAKING STRENGTH
2,500 lbs. 2,500 lbs.

PIN DIA
1/4" Ext. 5/16" Chainplate 1/4"

MAX ADJ.
1" 1-1/2"

O.R. THROW
2-1/4" 2-1/4"

PIN TO PIN
8-3/8" max. 7-3/8" min. 8-3/8" max. 6-7/8" min

SWL
1000 lbs 1000 lbs

Quick Release Levers
This new quick release lever is similar in principle to our popular 14-205/206 series. It is larger with an ultimate strength of 4000 lbs. It is supplied with either an extender for a terminal eye or a 5/32" or 3/16" wire swage terminal. Comes complete with a quick release pin for instant throw off. It features an over center lever intended for headstays on trailerable boats in the 30 ft. range and for inner forestays on larger boats.
NOTE: Quick Release Pins available - see chart page 37

Specifications & Data
CAT. NO.
14-200 14-210 14-211 14-212

14-211 14-212

TYPE
1/4-28 R.H. Female Lug only Extender Swage Term. Swage Term.

WIRE SIZE
1/8", 5/32" 5/32", 3/16" 5/32" 3/16"

APPROX. BREAKING STRENGTH
4,000 lbs. 4,000 lbs. 4,000 lbs. 4,000 lbs.

PIN DIA
5/16" 5/16" 5/16" 5/16"

MAX ADJ.
2-1/8" 1-1/2"
(4 HOLES)

O.R. THROW
2-5/8" 2-5/8" 2-5/8" 2-5/8"

PIN TO PIN CLOSED
Pin to Lug Center 6-1/8" 10-7/8" max. 9-3/8" min Depending on wire size Depending on wire size

SWL
1600 lbs 1600 lbs 1600 lbs 1600 lbs 14-210

2-1/8" 2-1/8"

Johnson Marine * Tel 860.873.8697 * Fax 860.873.8589 * www.csjohnson.com

27