Life Line Fittings - Machine Swage

Swivel, Single Gate Eye
A single eye is used on one end of the gate area to attach the gate hook.

22-311 22-317 22-313

1/8" wire 5/32" wire 3/16" wire

Adjuster-Short
23-303 24-305 35-620 24-303 35-621

Generally used at the stern rail in conjunction with the single gate eye to tension that section of the gate. 1/8" wire 1/4" pin 5/32" wire 1/4" pin 3/16" wire 1/4" pin 1" adj 1" adj 1" adj

Threaded, Single Gate Eye

Knurled Nut for 1/8", 5/32" size Knurled Nut for 3/16" size

Same as above only terminal is threaded into eye nut.

22-301 22-307 22-303 22-305-7 22-305

1/8" wire 5/32" wire 3/16" wire 1/4" wire 1/4" wire 7/32" swage

tain 16 S ll T-3 A

less!

Toggle Jaw, "T" Style
25-314 25-316 25-318-7

Generally used at the stern rail when no gate is required with a turnbuckle forward. 1/8" wire 1/4" pin 3/16" wire 1/4" pin 1/4" wire 5/16" Pin 7/32" swage

Swivel, Interlocking Gate Eye

22-312 22-318 22-314

1/8" wire 5/32" wire 3/16" wire

Toggle Jaw, Old Style
25-304 25-305 25-306 25-308 25-308-7

An interlocking gate eye is used at the opposite end of the gate hook as a "hinge" for the gate.

Same as above only uses toggle nut style instead of "T"bolt style. 1/8" wire 1/4" pin 5/32" wire 1/4" pin 3/16" wire 1/4" pin 1/4" wire 3/8" pin 1/4" wire 5/16" pin 7/32" swage

Threaded, Interlocking Gate Eye
Same as above only terminal is threaded into eye nut.

22-302 22-308 22-304 22-306-7 22-306

1/8" wire 5/32" wire 3/16" wire 1/4" wire 1/4" wire 7/32" swage

Deck Toggle - Old Style
This fitting can be used wherever a cable needs to be terminated to a deck or bulkhead. 3/4" to 1" 25-305-1 5/32" wire "old style"

Eye to Eye Fitting

This fitting can be used wherever an eye is required on each side of the stanchion. 22-100 Adjustable between 3/4" and 1"

Eye to Interlocking Gate Eye Fitting

Deck Toggle `T' Style
Same Deck Toggle only "T" bolt construction. 25-314-1T 25-316-1T 25-318-1T 1/8" wire "T-style" 3/16" wire "T-style" 1/4" wire "T-style"

This fitting can be used wherever an eye is required on one side, and an interlocking eye on the other side of a stanchion.

22-304-100

Adjustable between 3/4" and 1"

Techno*TIP

One of the most neglected parts on a sailboat are the Life Line and Rigging Turnbuckles. Turnbuckles need to be kept free of dirt and salt by rinsing with fresh water periodically. A good marine lubricant like Johnson Sealube or equivalent should be applied to the threads. The lubricant will provide corrosion protection and keep the turnbuckles turning freely. Never straighten a bent threaded stud, always replace it. A bent stud is considerably weakened.

Johnson Marine * Tel 860.873.8697 * Fax 860.873.8589 * www.csjohnson.com

11